Cartek Electronics

7 products

About Cartek Electronics

Cartek Automotive Electronics, based in Hamble near Southampton, makes solid-state electronics for race and rally cars: battery isolators, FIA rain lights, power distribution modules and panels, shift lights, gear indicators and a wireless steering wheel control system. At VMEP we supply the range.

Battery isolators

A Cartek isolator replaces the mechanical master switch. It stops the engine first, by cutting power to the ECU or ignition, then disconnects the battery negative from the chassis, which protects the alternator and electronics from voltage spikes. The driver uses an internal button; marshals use one or more external buttons. Each model is sold as the unit only or as a kit with a red or blue external button.

ModelSuitsEngine stop outputConnection
X-ClubProduction-based engines up to 3 litres and 6 cylinders10 AFlying leads
GTStandard ECUs and looms, and historic cars40 AFlying leads
XRMotorsport ECUs and PDMs only0.5 A signal5-pin Binder
X-ProAny car, up to V8 and V125 to 20 A, selectableDeutsch 4-pin

The full comparison, with sizes, weights and switching currents, is in our Cartek battery isolator guide. Which cars need an isolator, where the external switch goes and how it's marked are on our race car battery isolators page.

Rain lights, power and dash

  • Rain lights: the rectangular CK-LRS-15RM and circular CK-LRS-16CM, homologated to FIA 8874-2019, and the static CK-LR-15 to the 2008 specification, in horizontal or vertical mount.
  • Power distribution: the 8 and 16 channel Power Distribution Panel, which replaces fuses, relays and switches and is set up without a laptop, and the CK-PM-04 module with four 10 A channels.
  • Dash and wheel: shift lights and gear indicators in Club and OBD2 versions, and the wireless control system, with eight steering wheel buttons, with or without paddles.

For help choosing, or a Cartek part that isn't listed, call 01789 453 967 or email alex@vmep-ltd.co.uk.

01 Which Cartek battery isolator do I need?

Cartek's own guidance: cars with a motorsport ECU or PDM go for the X-Pro or XR; cars with a standard ECU and wiring go for the X-Club or GT; historic cars go for the GT. The X-Club is built for production-based engines up to 3 litres and 6 cylinders, and the X-Pro handles large, highly tuned engines up to V8 and V12.

02 Is a Cartek battery isolator FIA approved?

The FIA has no approval procedure for master switches, as it does for seats or extinguishers. Most FIA race and rally championships require a spark-proof master switch that cuts all electrical circuits and stops the engine, and Cartek says its isolators meet that. Check the wording in your own championship's regulations.

03 How much is a Cartek battery isolator?

At VMEP a Cartek isolator on its own costs £175 ex VAT for the X-Club, £225 for the GT, £240 for the X-Pro and £270 for the XR, or £220 to £325 as a kit with an external button. Rain lights are £85 for the 2008 specification and £135 for FIA 8874-2019. UK orders add 20% VAT.

04 Do I have to connect the engine stop output?

Yes, if the car has an alternator. Disconnecting the battery alone won't stop the engine, because the alternator keeps generating power. The isolator cuts the ECU or ignition first, then the battery, so wire the engine stop output to your ignition or ECU power.

05 Which Cartek rain lights meet FIA 8874-2019?

The rectangular CK-LRS-15RM (homologation RL.009.22) and the circular CK-LRS-16CM (RL.010.22). Both are at least 800 cd and run static or flashing at 4 Hz, on 11.3 to 15.6 V. The static CK-LR-15 is homologated to the older 2008 specification. Your series rules say which you need.

06 What is a PDM in a race car?

A power distribution module replaces fuses and relays with solid-state switching. Each channel protects its circuit against over-current and short circuits, shuts down safely and shows the fault on an LED. Cartek's Power Distribution Panel combines that with the switch panel: 8 or 16 channels set to 5, 10 or 15 A, with no laptop needed.

07 Can I use my own switches with a Cartek isolator?

Yes. Cartek says the internal switch must be a latching type and the external switch a momentary type, pushed to break the connection. You can fit more than one external button, for example one on each side of the car.

Also distributed by VMEP